full20_32437Pullers_Hydraulic_Push_Pullers
full20_36260Pullers_PPH30full20_36259Pullers_PPH17full20_36246Pullers_PPH50full20_31195Accessories_Push_Pullers_Legs_3full20_31194Accessories_Push_Pullers_Legs_2full20_31192Accessories_Push_Pullers_Legs_1full20_31152Pullers_IPS5017_App1full20_31153Pullers_IPS3017_App1

Hydraulic Push-Pullers


Category: .
Hydraulic Push-Pullers – 17 1/2, 30, 50 Ton

The power to make impossible jobs become routine.

  • Can apply a hydraulic pushing or pulling force, depending on how the puller is set up.
  • Each unit includes perfectly matched hydraulic components that can be detached from the Push- Puller® for other tasks requiring dependable Power Team power; assuring maximum return on your investment.
  • Optional leg kits adapt your Push-Puller® to extra long or extra short reach.
  • A wide variety of threaded adapters, bearing pulling attachments and internal pulling attachments can be used in combination with our Push-Pullers®.

Selection and capacity rating – Each Push-Puller’s specified tonnage “capacity” is determined using its standard legs in tension. Using longer legs, or a setup in which the legs are in compression, will reduce the “capacity”. Always select the largest “capacity” puller and the shortest legs that will fit the job.

Power Twin® cylinder – This unique center-hole cylinder powers each Push-Puller®. Puller screw runs right between the twin spring cylinder. A basic head allows you to change from a tapped hole to a plain hole by merely changing the head insert.

17 1/2 Ton Capacity, Push-Puller®:
Order No. Cap.
(tons)
Description Weight (lbs)
1062 17 ½ Puller only.  (Cylinder, pump, hose, coupler, screw, and crank not included). 20.0
Packages:
PPH17 17 ½ Push-Puller® with RT172 center-hole Power Twin® cylinder, cylinder half coupler, P55 pump, 9767 6-ft. poly-urethane hose, 9798 hose half coupler, 16 1/2″ legs, 24827 leg ends, 1″-8 x 20″ lg. adjusting screw (32118) and adjusting crank (24814). 59.0
PPH17R 17 ½ Same as above, but without P55 pump, 9767 6-ft. poly-urethane hose and 9798 hose half coupler. 40.0

USE WITH:

 Order No. Description 
679 Pulley Pulling Attachment
1104 16 1/2″ Puller Legs
1105 22 1/2″ Puller Legs
1106 9 1/2″ Puller Legs
1107 4 1/2″ Puller Legs
1108 30″ Puller Legs
1124 Bearing Pulling Attachment
1130 Bearing Pulling Attachment
1154 Internal Pulling Attachment
Pair of puller legs for 17 1/2-ton “capacity” Push-Puller®.

NOTE: L = leg length: 4 1/2″, 9 1/2″, 16 1/2″, 22 1/2″, 30″; subtract 4 7/8″ from leg length to determine reach when using leg end caps.

Leg Ends – Upper leg ends are threaded 3/4″-16″ lg.  Lower leg ends are threaded 5/8″-18″ lg.

30 Ton Capacity, Push-Puller®:

Order No. Cap.
(tons)
Description Weight (lbs)
1070 30 Puller only. (Cylinder, pump, hose, coupler, screw and crank not included.) 42.0
Packages:
PPH30 30 Push-Puller® with RT302 center-hole Power Twin® cylinder, cylinder half coupler, P55 pump, 9767 6-ft. polyurethane hose, 9798 hose half coupler, 18″ legs (1110), 28390 leg ends, 1 1/4″-7 x 24″ lg. adjusting screw (34758), and adjusting crank (27198). 102.0
PPH30R 30 Same as above, but without P55 pump, 9767 6-ft. polyurethane hose and 9798 hose half coupler. 82.0

USE WITH:

 Order No. Description 
679 Pulley Pulling Attachment
680 Bearing Pulling Attachment (Use two 8012 adapters to connect to puller.)
1109 8″ Puller Legs
1110 18″ Puller Legs
1111 28″ Puller Legs
1166 Internal Pulling Attachment
Pair of puller legs for 30 ton “capacity” Push-Puller®.

NOTE: L = leg length: 8″, 18″, 28″; subtract 5 7/8″ from leg length to determine reach when using leg end caps.

Leg Ends are threaded 1″-14 x 1 1/4″ lg.

50 Ton Capacity, Push-Puller®:

Order No. Cap.
(tons)
Description Weight (lbs)
1076 50 Puller only. (Cylinder, pump, hose, coupler, screw and crank not included.) 106.0
Packages:
PPH50 50 Push-Puller® with RT503 center-hole Power Twin® cylinder, cylinder half coupler, P55 pump, 9767 6-ft. polyurethane hose, 9798 hose half coupler, 24″ legs (1112), 1 5/8″-5 1/2 x 30 3/8″ lg. adjusting screw (32698), and adjusting crank (29595). 201.0
PPH50R 50 Same as above, but without P55 pump, 9767 6-ft. polyurethane hose and 9798 hose half coupler. 181.0

USE WITH:

 Order No. Description 
1112 24″ Puller Legs
1113 34″ Puller Legs
1128 Bearing Pulling Attachment
Pair of puller legs for 50 ton “capacity” Push-Puller®.

Leg Ends are threaded 1 1/4″-12 x 1 3/4″ lg.

 Hydraulic Push-Pullers - Typical Setup

ASSEMBLING THE TOOL TO APPLY PUSHING OR PULLING FORCE:

1. Determine if you want the tool’s forcing screw to push or pull.

2. To exert pushing force, the forcing nut is installed beneath the cross block, as shown on left.

3. To cause the forcing screw to pull, the forcing nut is placed on top of the cross block.

4. The sliding plates must always be placed on the opposite side of the cross block from the forcing nut.

Catalog

Related Products

  • full20_32394Pullers_Mechanical_Push_Puller

    Mechanical Push-Pullers

  • full20_31106Pullers_PHP8H

    Manual-Hydraulic Pusher

  • full20_380611182

    Lock-on Jaw-type Puller Set

  • full20_28293671x386_PH83C_Case_Open

    Hydra Grip-O-Matic Set